China Customised Tank

The reason why the titanium tube is used is that it has many advantages such as light weight, high temperature resistance, corrosion resistance, and the filter element can be used repeatedly. The specific cleaning selection depends on whether the impurities in the filtrate are acidic stainless steel Bright beer tanks manufacturers or alkaline. And pay attention to cleaning when using the titanium rod filter. Backflushing or backwashing is required, and the regeneration period is determined according to the rated pressure and flow rate.

Titanium rod filters are generally used for intermediate filtration, and are widely used in the pharmaceutical industry, complying with national standards.. When in use, it usually takes five minutes to start the interior at low pressure. The filter element inside is too used. During use, it is necessary to avoid scratches and collisions, and its working pressure must not exceed the rated working pressure.The titanium rod filter is generally made of stainless steel. It can accurately ensure the accuracy of filtration, reduce operating costs, and has a wide range of applications.

After all, it can be used as common sense to understand. The lower part of the sewage outlet should also be considered. The sewage pipe should not be too long, and the instructions in the manual should be strictly followed. It has the advantages of good sealing, easy operation, and good circulation.. In the chemical industry, it is used to produce weakly corrosive materials, and it is also used for low-temperature materials in refrigeration, and finally in light industrial food and non-products as long as there are sanitary requirements.

During installation and use, attention should be paid to the protection of the control box and sensors. The duplex filter is a three-dimensional connection with two stainless steel filters in parallel.Except those in the industry, people don't know much about duplex filters. Here is a brief introduction

The surface is smooth, no cracks, no bubbles in the welding seam, and the lining structure should be well-balanced and free of burrs. , Again aggravate corrosion. The special inteal tie rod structure makes the mechanical performance more reasonable. The welding rod adopts stainless steel electrode, ER308L, all adopt the tungsten argon gas shielded welding process;  After making and installing, make full water test. How is the stainless steel combined water tank made? Understand briefly.

The traditional repair welding method is more difficult, and thermal stress will cause greater damage to the equipment; brushing epoxy-type corrosion-resistant materials will cause cracks and peeling due to the surface adhesion and expansion coefficient.The stainless steel combined water tank uses a special sealing strip and a fully bolted connection structure, which is easy to assemble, Bright Beer Tanks factory and will not leak or leak tightly. Before welding, the groove should be grooved according to the regulations of GB/T985-1998, and the outer dimension of the weld should conform to the regulations of JB/T794-1999 , And to ensure that there is no false welding, no slag inclusion; 3. There are no special requirements on the installation site. The shape should meet the requirements of the user, and the volume can meet all design requirements.

At present, most effective methods use polymer composite materials, among which the Fuschlan series are more mature. The stainless steel combined water tank is generally made of Cr stainless steel. For different equipment, different operating conditions, and different forms of corrosion and leakage, the use of corresponding technical products can quickly, simply and effectively protect the equipment, especially due to the comprehensive performance of polymer composite materials such as chemical corrosion resistance and bonding performance It avoids the adverse effects of traditional repair welding and protection of traditional anti-corrosion materials, makes the repaired equipment life even longer than new equipment, fundamentally solves the cause of corrosion and leakage, helps companies improve equipment management and reduce maintenance Cost and improve the competitiveness of enterprises.

The stainless steel combined water tank is the most widely used alteative to the FRP water tank in the construction industry. Because the material does not contain nickel, the corrosion and leakage problems of the welding part of the water tank during use are more common. 1. After the installation of the water tank is completed, clean and decontaminate inside and outside. Standard molded panels; free assembly, no lifting equipment. 

1. This operation is controlled by the inlet ball valve. When the pressure is no longer increased and does not exceed the rated operating pressure, the process time shall not be less than 3 minutes; When the air release valve spray liquid, close the air release valve; 3. Connect pure air, open the back-blowing valve and use a back-blowing pressure of more than 20% of the filter pressure, back-blowing 2 to 3 times, each for 3 to 4 seconds; 7.Titanium rod filters are widely used in decarbonization and filtration in the pharmaceutical and chemical industries such as large infusion and injection production lines.

Each time it decreases, the backflushing pressure should be increased and the backflushing time should be extended; Bacteria treatment can be sterilized by steam at 121°C for 30 minutes. Open the air release valve first, and then open the ball valves at the inlet and outlet; Pay attention to the air release valve after tuing on the pump. Observe the drain outlet until the clean liquid is discharged. After connecting the stainless steel beer tanks filter, backflush with distilled water for 5-15 minutes.

Observe the gauge pressure pointer, the gauge pressure should be increased slowly. At present, more and more titanium rod filters are used, but how do they operate and how to use them correctly and safely? The following steps are detailed steps for you to take a look. The backflush pressure should be greater than the filter pressure; After backflushing, close the blowdown valve, prepare for the next batch of filtration process, and observe the filtration flux of the previous batch.

After backflushing, close the backflush valve and open the ball valve of the feed inlet.. Observe the holding time of constant pressure and the quantity of materials and calculate the unit flow; 5． After filtering a batch of materials, close the inlet and outlet ports and open the drain valve; 6

When the material enters, it is set in the high temperature barrel. Sterilization equipment. When it retus to the double coil, the material is It enters the inner flow channel and is cooled by the outer cold material, so that the discharge temperature is significantly reduced (generally lower than 65°C). The throttle valve of the ultra-high temperature instant sterilizer can be adjusted. The material is finally removed by the three-way cock. If the process needs to increase or decrease the discharge temperature, the angle shut-off valve can be activated to connect the heat source (steam) or heat source (water or ice water, etc.

When the high-temperature coil is China Wholesale beer brewhouse factory heated, it is heated to the required sterilization temperature due to the indirect heating of the steam in the barrel, and then the temperature is kept in the single coil outside the barrel to kill the bacteria of the material. The upper end of the feed three-way cock is connected with the storage tank, and the lower end is connected with the material source pipeline. The lower end of the cock is connected to the spiral tube, and the outlet of the plug will be the storage tank.. When the processing capacity needs to be improved, the 'U'-shaped tube can be removed and a centrifugal pump can be connected. When necessary, the spiral tube can be rotated to align with the overflow tube.

The sterilization process of the material of the ultra-high temperature instant sterilizer: The material enters the outer flow channel of the double coil through the feed pump, and the hot material flowing out from the inner layer is indirectly heated to get preheated. On the one hand, the material is maintained under a certain pressure and its boiling point temperature is increased to prevent vaporization; on the other hand, it is also used to adjust the flow rate. The sterilization temperature is adjusted by an angle stop valve, and the discharge temperature can be changed by an angle stop valve. The ultra-high temperature instantaneous sterilization machine contains a pressure container—a high temperature barrel in the host, which is used to fill pressure steam.) to the outer flow channel at the lower end of the double sleeve.

The feeding and discharging of the ultra-high temperature instant sterilizer adopts three-way cock, and the flow can be adjusted according to the needs, and the use is reliable.We all know that the ultra-high temperature instantaneous sterilizer is suitable for instantaneous sterilization of liquid materials such as fresh milk, fruit juice, beverages, popsicles, and ice cream slurry, soy sauce, soy milk, condensed milk, alcohol, etc. The main setting outside the barrel is a spiral double sleeve, which is used to exchange cold and heat for incoming and outgoing materials; the main setting inside the barrel is a spiral single tube that is used to receive heat indirectly.

The steam pressure gauge, sterilization temperature gauge and discharge temperature gauge are all installed on the host. At present, it is also widely known and used, but how does the ultra-high temperature instantaneous sterilizer work specifically, let's lea more about the working principle of the ultra-high temperature instantaneous sterilizer. The ultra-high temperature instantaneous sterilizer is a hand-controlled sterilizer. It can also be used for fluid materials

　　 Refrigerating and adding carbon dioxide to keep the beer fresh can ensure the hygiene of beer and extend the shelf life, which provides conditions for beer long-distance transportation and sales. In order to further expand the market, we are now looking for partners, agents and distributors from various channels at home and abroad, with good quality and good reputation. 

The draft beer machine is mainly composed of a refrigerator, draft beer barrels and carbon dioxide cylinders. So what are the functions of the draft beer machine? Next, the editor will introduce to you. By refrigerating and adding carbon dioxide, the beer is fresher, thicker and richer in foam; 　

We believe that good products can create more value for customers. It continuously develops high-performance draft beer machines, and designs for customers a variety of unique wine nozzles, such as single nozzle, double nozzle, and four nozzles. Refrigeration and refrigeration provide a suitable beer drinking temperature, making it more refreshing and endless aftertaste; 　　

With the continuous development of technology and the further improvement of people’s living standards, in order to meet consumers’ needs for diversified nutrition and taste, the draft beer machine adopts high-tech fresh beer filtering technology, which not only retains the fresh taste of draft beer, but also in addition to harmful bacteria and Impurities, retain the original nutrients, make the foam more delicate, the taste is more refreshing, and further enhance the pleasure of beer bright beer tank manufacturers to people. It is deeply loved by beer lovers for its rich and delicate foam and refreshing taste